The average cost for a roof inspection in the year 2021 is $348. There are several factors that can cause this price tag to either increase or decrease, though. Let's take a look at some roofing variables in Payson, Arizona.

Types Of Roof Inspections

Homeowners can request inspection services for all sorts of different reasons. Perhaps a large storm has just passed through the area or a storm is on the way. Or, as is usually the case, a homeowner will request an inspection just for peace of mind. Knowing your roof is in good condition ensures the safety of your family. This is the most common reason why one requests an inspection.

Getting ready to buy or sell a home calls for a thorough roof inspection. These crucial inspections can alter the price of the home depending on the condition of the roof. When requested, a roof inspection can simply include a check for any leaks in and around the roofing area. Leaks can take a huge toll on utility bills. Leak repairs and insulation costs could result from any sort of leakage that occurs.

Typical Roof Inspections

Most roof inspections will include check of the underlayment, counter flashings, drip-edge flashing and shingles. The inspector will make sure all of these are installed properly and in good working condition for the longevity of your home. Most inspectors are also likely to go into your attic for a look at the underside of the roof. This area is also referred to as the decking.

All roof inspections, averaging a cost of $326, will include checks of gutters, shingles, rooftop vents and flashings. Costs will vary based on square footage for most roofing companies. Steeper roofs or ones with multiple levels will generally cost more to inspect. Additional charges may be added on due to your location. If the inspection requires a lot of travel time for the inspector, you can expect to pay around $60 extra for the service.

Roof Inspection Costs

• Lowest price: $100
• Highest price: $1,000
• Average price: $348

Roof Repair In Payson, Arizona

Right Way Roofing, Inc. offers residential roof repair and commercial roof repair in Payson, Arizona and surrounding cities. If you need a new roof installed or replaced, Right Way Roofing, Inc., is the right way to go! Contact us or call us at 602-299-8851 for more information.

The average cost for a roof inspection in the year 2020 is $326. There are several factors that can cause this price tag to either increase or decrease, though. Let's take a look at some roofing variables in Payson, Arizona.

Types Of Roof Inspections

Homeowners can request inspection services for all sorts of different reasons. Perhaps a large storm has just passed through the area or a storm is on the way. Or, as is usually the case, a homeowner will request an inspection just for peace of mind. Knowing your roof is in good condition ensures the safety of your family. This is the most common reason why one requests an inspection.

Getting ready to buy or sell a home calls for a thorough roof inspection. These crucial inspections can alter the price of the home depending on the condition of the roof. When requested, a roof inspection can simply include a check for any leaks in and around the roofing area. Leaks can take a huge toll on utility bills. Leak repairs and insulation costs could result from any sort of leakage that occurs.

Typical Roof Inspections

Most roof inspections will include check of the underlayment, counter flashings, drip-edge flashing and shingles. The inspector will make sure all of these are installed properly and in good working condition for the longevity of your home. Most inspectors are also likely to go into your attic for a look at the underside of the roof. This area is also referred to as the decking.

All roof inspections, averaging a cost of $326, will include checks of gutters, shingles, rooftop vents and flashings. Costs will vary based on square footage for most roofing companies. Steeper roofs or ones with multiple levels will generally cost more to inspect. Additional charges may be added on due to your location. If the inspection requires a lot of travel time for the inspector, you can expect to pay around $60 extra for the service.

Roof Inspection Costs

• Lowest price: $100
• Highest price: $1,000
• Average price: $326

Roof Repair In Payson, Arizona

Right Way Roofing, Inc. offers residential roof repair and commercial roof repair in Payson, Arizona and surrounding cities. If you need a new roof installed or replaced, Right Way Roofing, Inc., is the right way to go! Contact us or call us at 602-299-8851 for more information.

Metal roofing is a terrific option for homeowners in Payson, Arizona. In order to install this roofing material, though, the metal sheets must be cut to fit onto your roof. Fortunately, cutting this material is quite easy when a few simple rules are followed.

Metal Roof Cutting Procedure

Cutting a metal roof sounds like an easy enough process, but homeowners must pay attention to details when beginning the procedure. The first thing to do is to lay the roofing sheets on a flat surface. Make sure the underside is facing upwards. Then pin the sheet in place with adjustable clamps.

Calculating the actual number of panels needed for your roof is crucial. Roof measurements, of course, are perhaps the first step in any process towards roofing repairs, replacements or installations. You will need to know how large the panels need to be and how to go about cutting them. Use a tape measurer to plan your potential panel cuts.

Lastly, prepare for any risks by putting on safety gear. Cutting metal can create a lot of dust in the air. Stay safe by putting on goggles, a mask and gloves. Go out and buy these supplies if you don't already have them available in your home. If you're looking to limit the dust and debris generated, then refrain from using a circular saw. This tool generally produces more debris than any other material used for cutting.

Tools For Cutting

There a few suggested tools to use when cutting metal roofing. With 29-guage metal roofing panels, a circular saw with a metal blade can be used to cut through this tough material. One issue with using this tool, though, is that it tends to cut too fast. Be careful with the speed at which you cut with the saw. Cutting too quickly can lead to paint damage on the panels. Paint damage will lead to unwanted rust in the years to come.

Metal shears are another popular tool used to perform this task. Again, cutting metal roofing with this tool is not always easy. Using metal shears can be a tedious and long process, but it offers the best and most efficient results. The last thing you want to find out is your cutting sizes are a bit off when you go to install this roofing type. Make constant short cuts with this tool. Taking the time to be efficient with this tool is very important.

If a starting point is desired, feel free to drill a small hole in the roofing material. An electric drill should work just fine. Then, use the shears to cut, using the pilot hole as a guide. If you are simply planning to cut end to end, then a pilot hole is not necessary. Hammering a nail or using a screwdriver to create a hole is effective, as well, but will take more time than an electric drill would for this process.

Cutting Steps

• Mark the metal ahead of cutting.
• Figure out how many panels your roof needs.
• Put on protective gear before cutting begins.
• Perform cutting process.

Metal Roofing In Payson, Arizona

Right Way Roofing, Inc. offers residential roof repair and commercial roof repair in Payson, Arizona and surrounding cities. If you need a new roof installed or replaced, Right Way Roofing, Inc., is the right way to go! Contact us or call us at 602-299-8851 for more information.

There are 8 common roofing problems that occur in the heart of Arizona. Poor ventilation, water damage and holes are just a few issues homeowners in Payson, AZ may experience.

Fallen Trees

Trees seemingly always pose a threat to your roof, whether it is made of asphalt or metal. The protective top layer of your roofing can easily be punctured or damaged by a fallen tree caused by inclement weather or other factors. Trimming tree branches regularly is one of the only ways a homeowner can prevent this potential issue.

Poor Ventilation

A proper ventilation system is crucial for the longevity of any roofing style. This will help regulate moisture that builds up over time. Poor ventilation can result in damage to shingles, insulation, sheathing and rafters, among other areas. Your energy costs will certainly increase with poor ventilation, as well.

Water Damage

Water damage can be devastating to your home and its value over time. the biggest issue with water damage related to roofing is that it can be invisible. Many times a professional will have to inspect and remove shingles just to check for this issue. So, not only is water damage incredibly harmful, it will also cost you the services of a professional. Regardless, this is a problem that cannot be simply ignored.

Drainage Issues

Drainage issues can lead to other problems for your roof. Water damage is, of course, at the top of that list. If you have a flat roof, always pay attention to any sort of staining. This is a sign of collecting water atop your roof. Keep your gutters clear with routine maintenance if you have a slanted roof.

Holes

Holes can be produced in many ways. Inclement weather, fallen trees and even smaller critters can create holes atop your roof. Holes will lead to moisture and critters getting inside your home. Heating and cooling bills can skyrocket when roofing holes go undetected.

Lack Of Maintenance

Not performing routine maintenance is the biggest disservice you can do to your roof. Clogged gutters or fallen tree branches can cause serious damage if not taken care of. Keep up with regular maintenance now and you will save money in the future.

Leaks

Leaks may be the most common roofing problem today. All inclement weather carries water, including rain, hail, snow and ice. The worst possible outcomes associated with roofing leaks are mold and rotting. Always check your roof's condition after a storm has passed over the area.

Expensive Repairs

Of course, all seven of the previously mentioned issues can occur simply because homeowners do not want to pay for regular repairs or maintenance. Regardless of the type of roofing, repairs will always be costly. Costs can run anywhere from $120-$1,500 per 100 square feet, depending on the material. Always call your local professionals to get a quote ahead of any repairs.

Metal Roof Repair Payson, Arizona

Right Way Roofing, Inc. offers residential roof repair and commercial roof repair in Payson, Arizona and surrounding cities. If you need a new roof installed or replaced, Right Way Roofing, Inc., is the right way to go! Contact us or call us at 602-299-8851 for more information.

Metal roofing is a fantastic way to conserve energy and cut down on noise pollution. That's why many commercial buildings and homes are utilizing this roofing option lately. Here are 5 metal roof insulations tips in the Payson, AZ area.

• Always use foam batting
• Use staples
• Panel gaps
• Cut roof panels
• Paper liner for insulation

Keep reading for full metal roof insulation tips.

Always Use Foam Batting

Foam batting is by far the best and most common material used for metal roof insulation. This form comes in panels, as opposed to paper covered fiberglass. Foam batting is convenient to use because it lays flat under the metal roofing and can be installed with ease. Additionally, this foam can be used on either the inside or outside of the sheathing.

Use Staples

Staples are surprisingly best suited to hold down metal roofing insulation. 1.5-inch staples is the recommended size to use for this task. Staples can penetrate several sheets of insulation while holding steady for long periods of time. Staples will not make large holes or dents in the insulation.

Panel Gaps

Metal roofs need to be able to breathe, as with most roofing materials. You want to allow airflow around the surface by leaving gaps between the panels. Gaps between panels are vital to the health and long-term existence of the roof.

Cut Roof Panels

So, how can a homeowner create these gaps between panels? The answer is actually quite simple. Measure out all materials before starting the process of insulation. Then, manually cut the foam panels. This will create the proper gapping and helps make the laying process much quicker and more efficient.

Paper Liner For Insulation

Forgetting or neglecting to lay down any type of paper wrap on the sheathing with the metal roofing is a common mistake for homeowners. Laying down paper wrap is a crucial step towards insulation. The paper is meant to protect the home by keeping water buildup from getting underneath the roofing.

Tile Roof Repair Payson, Arizona

Right Way Roofing, Inc. offers residential roof repair and commercial roof repair in Payson, Arizona and surrounding cities. If you need a new roof installed or replaced, Right Way Roofing, Inc., is the right way to go! Contact us or call us at 602-299-8851 for more information.